collapse

Welcome!



Welcome to Robot Rebels, an online robot maker community.

Register today to post your projects, ask questions, share knowledge and meet like-minded people from around the world.


The RobotRebel.org Community

Author Topic: 24byj48 based delta robot - fail  (Read 1999 times)

mogul

  • Hot glue gunslinger
  • Member
  • *
  • Posts: 151
  • This is a good day!
24byj48 based delta robot - fail
« on: October 08, 2017, 02:24:55 AM »
I made this small delta robot.
fast-move.jpg
*fast-move.jpg (48.73 kB . 602x768 - viewed 225 times)

It is fast as should be


But after the first few movements it is obvious that the cheap 24byj48 motors have way too much play. At some positions where center of gravity is right (bad), the end effector's position is floating more than 10mm in a random direction.

Not sure if it really make sense to continue down this path.
« Last Edit: October 08, 2017, 01:16:47 PM by mogul »

 

* Search


* Recent Topics

Just scary to me... by VirgilReevy
[Today at 05:04:43 AM]


Vous ne savez pas comment m'aider? by VirgilReevy
[Today at 05:03:28 AM]


Just a short intro... by MEgg
[March 18, 2019, 05:49:28 PM]


MKS GEN L Servo Issue by cmptrguy1
[March 14, 2019, 01:18:28 AM]


Yes I am alive! by jinx
[March 10, 2019, 04:38:53 AM]


CZ-1 2.0: problems, calibration and printing, part2 by MEgg
[February 26, 2019, 03:35:15 PM]


Hi, Mushroom glue here. by nschreiber0813
[February 25, 2019, 02:09:13 PM]


Arduino IK by BaldwinK
[February 25, 2019, 05:54:44 AM]


Raspberry Pi / Python eBook - free for the next 11 hours! by MEgg
[February 24, 2019, 09:49:43 AM]


MKS Gen L 1.0 by MasterDomino
[February 24, 2019, 06:34:24 AM]


Fun Fact by Impala
[February 13, 2019, 11:05:01 PM]


Animabot Rev3 - Advanced Hexapod Robot by Smashley
[February 05, 2019, 03:41:50 PM]


Finally tried out a Chinese PCB service by Bajdi
[February 02, 2019, 08:40:49 AM]


PLX-DAQ by BaldwinK
[January 16, 2019, 06:44:18 AM]


Four Motor Leg Module by BaldwinK
[January 09, 2019, 04:55:14 PM]

* Recent Posts

Re: Just scary to me... by VirgilReevy
[Today at 05:04:43 AM]


Vous ne savez pas comment m'aider? by VirgilReevy
[Today at 05:03:28 AM]


Re: Just a short intro... by MEgg
[March 18, 2019, 05:49:28 PM]


Re: Just a short intro... by Killer Angel
[March 18, 2019, 06:55:35 AM]


Re: Just a short intro... by jinx
[March 16, 2019, 04:36:13 AM]


Re: Just a short intro... by Bajdi
[March 15, 2019, 04:22:09 PM]


Just a short intro... by cybersamurai
[March 15, 2019, 04:19:22 PM]


Re: MKS GEN L Servo Issue by cmptrguy1
[March 14, 2019, 01:18:28 AM]


Re: Yes I am alive! by jinx
[March 10, 2019, 04:38:53 AM]


Re: Yes I am alive! by nschreiber0813
[March 09, 2019, 03:59:04 PM]


Re: CZ-1 2.0: problems, calibration and printing, part2 by MEgg
[February 26, 2019, 03:35:15 PM]


Re: Hi, Mushroom glue here. by nschreiber0813
[February 25, 2019, 02:09:13 PM]


Yes I am alive! by nschreiber0813
[February 25, 2019, 02:08:12 PM]


Arduino IK by BaldwinK
[February 25, 2019, 05:54:44 AM]


Re: Raspberry Pi / Python eBook - free for the next 11 hours! by MEgg
[February 24, 2019, 09:49:43 AM]