collapse

Welcome!



Welcome to Robot Rebels, an online robot maker community.

Register today to post your projects, ask questions, share knowledge and meet like-minded people from around the world.


The RobotRebel.org Community

Author Topic: Sbase and the reprap full graphics smart controller  (Read 472 times)

jinx

  • calling from free Europe
  • Moderator
  • Sr. Member
  • *****
  • Posts: 440
Sbase and the reprap full graphics smart controller
« on: March 27, 2018, 05:26:38 PM »
                   

         I came across a rather annoying issue with the Sbase 1.3 and the reprap full graghic smart controller,  which to be honest hasn't been documented well at all on the WWW.  by default smoothieware  comes with the panel section for the controller leaving the user to uncomment to activate it.
           The problem after configuring smoothieware and installing the controller ribbon cables to the sbase, am left with the dreaded blank screen and the occasional bleep!.  After reading some drastic solution on the web ie under powered, user error in configuring  with some  other rather drastic measures of needing to add extra resistor to the contrast pot on the controller etc..

           The solution this time was rather simple and it comes down to having to rotate the ribbon  headers 180 have to cut out some notches in the headers to allow the ribbon conns to fit     
               

once that done and plugged in all should be good.

               

 just go back to firmware and fine tune those panel  setting and spare yourself and disable the buzzer! happy printing .
     
         
       
         
« Last Edit: March 28, 2018, 02:03:35 AM by jinx »
I build bots

Bajdi

  • Member
  • *
  • B
  • Posts: 75
Re: Sbase and the reprap full graphics smart controller
« Reply #1 on: March 30, 2018, 08:57:01 AM »
I had to do the same thing to get my reprap full graghic smart controller to work with my re-arm/ramps.

jinx

  • calling from free Europe
  • Moderator
  • Sr. Member
  • *****
  • Posts: 440
Re: Sbase and the reprap full graphics smart controller
« Reply #2 on: March 30, 2018, 11:03:45 AM »
you have to swap the headers aswell?  like ext 1 goes to 2 and 1 to 2 on , common fault with the ramps adapter,  what I first thought  with the sbase  just I didn't have to swap cables round! took a morning too work that out  :'(.
I build bots

 

* Search


* Recent Topics

Sloooow progress on the I3 clone by KingBeetle
[July 16, 2018, 04:20:59 AM]


ESP32 - Stepper - LIDAR - Platform by jinx
[July 15, 2018, 04:58:51 AM]


MKS Gen L 1.0 by jinx
[July 15, 2018, 03:55:57 AM]


Motor rewinding machine by 1 what
[July 10, 2018, 06:03:46 PM]


All the stories in the forum are most important. by ZeroMax
[July 01, 2018, 09:44:53 PM]


Parallax CR Servo with Built-In Encoder by 1 what
[June 28, 2018, 12:13:32 PM]


He's Back...BoB V3.0 by k120189
[June 21, 2018, 07:03:17 PM]


Funding by MEgg
[June 21, 2018, 04:34:36 PM]


Robot Hive by jinx
[June 12, 2018, 03:58:03 AM]


Hi, Mushroom glue here. by Andrewsz
[June 11, 2018, 12:23:20 AM]


CZ-1 2.0: problems, calibration and printing, part2 by MEgg
[June 10, 2018, 06:10:53 AM]


Greetings! by Protowrxs
[June 05, 2018, 04:45:02 PM]


Raspberry Pi / Python eBook - free for the next 11 hours! by MEgg
[June 04, 2018, 05:21:07 PM]


All metal Titan Extruder by jinx
[May 27, 2018, 04:24:23 AM]


UConduit H-Bot printer design by KingBeetle
[May 26, 2018, 02:10:38 PM]

* Recent Posts

Re: Sloooow progress on the I3 clone by KingBeetle
[July 16, 2018, 04:20:59 AM]


Re: Sloooow progress on the I3 clone by MEgg
[July 15, 2018, 08:44:53 AM]


Re: ESP32 - Stepper - LIDAR - Platform by jinx
[July 15, 2018, 04:58:51 AM]


Re: MKS Gen L 1.0 by jinx
[July 15, 2018, 03:55:57 AM]


Re: Sloooow progress on the I3 clone by jinx
[July 15, 2018, 03:46:18 AM]


Re: MKS Gen L 1.0 by KingBeetle
[July 14, 2018, 04:05:49 PM]


Re: Sloooow progress on the I3 clone by KingBeetle
[July 14, 2018, 11:13:35 AM]


Re: ESP32 - Stepper - LIDAR - Platform by 1 what
[July 14, 2018, 07:02:46 AM]


Re: Sloooow progress on the I3 clone by MEgg
[July 14, 2018, 05:38:34 AM]


Re: Sloooow progress on the I3 clone by KingBeetle
[July 14, 2018, 03:45:21 AM]


Re: ESP32 - Stepper - LIDAR - Platform by jinx
[July 14, 2018, 02:49:04 AM]


Re: ESP32 - Stepper - LIDAR - Platform by 1 what
[July 13, 2018, 10:03:12 PM]


Re: ESP32 - Stepper - LIDAR - Platform by Gareth
[July 13, 2018, 04:19:01 PM]


Re: ESP32 - Stepper - LIDAR - Platform by jinx
[July 13, 2018, 01:33:15 PM]


ESP32 - Stepper - LIDAR - Platform by Gareth
[July 13, 2018, 04:28:46 AM]